MAMO DRONE Connector Cleaner-Preservative for Drones with Precision Nozzle 100 ml
249.00 грн
Cleans drone connectors from moisture, dirt and oxidation, and immediately covers contacts with a thin silicone film against oxidation — for connectors stored in moisture between flights. For XT30/XT60/XT90, balance, antenna SMA, USB, battery terminals; not for soldering boards. Spot nozzle: 3–5 presses, 2 minutes drying. 100 ml — approximately 100 connectors.
per item:
MAMO DRONE connector cleaner-preservative for drones — a “two-in-one” product: cleans electrical connections of UAVs from moisture, dirt and oxidation, and immediately covers contacts with a thin invisible silicone film against oxidation. For connectors that are stored or operate in humid environments between flights: bunkers, basements, cases in damp conditions.
A long rotating nozzle reaches inside XT30/XT60/XT90, balance, antenna SMA, USB and battery terminals. The film does not conduct current and does not interfere with the connection. Do not use on boards before soldering or varnish — for that use “Dry Contact Cleaner”.
Benefits
- Cleans and preserves in one pass — one bottle instead of two
- Silicone film prevents oxidation from starting again
- For connectors that stay in moisture between flights
- Spot nozzle — jet inside the connector, no spray
- Film does not conduct current, does not interfere with connection
- Does not freeze, pump without pressure
- 100 ml — approximately 100 connectors
Application method
- Disconnect power, remove battery.
- Unfold the nozzle, insert into the connector or direct at contacts from a distance of 2–3 cm.
- Make 3–5 presses. Remove dirt and oxides with a brush, repeat.
- Let dry for 2 minutes — a protective film remains on the contacts.
- Can be connected immediately. Update after contact with water or every 10–15 connections.
- Do not apply on boards before soldering or varnishing.
For which connectors. Power XT30/XT60/XT90, balance JST-XH, signal, antenna SMA/MMCX, USB, battery terminals. Not intended for boards, solder joints and optics.
Consumption. 3–5 presses (≈ 1 ml) per connector. 100 ml bottle — 80–100 connectors.
Composition: isopropanol 85–90 %, dearomatized hydrocarbon solvent < 10 %, dimethicone < 5 %.
Specifications
| Parameter | Value |
|---|---|
| Brand / line | MAMO DRONE |
| Type | electrical contact cleaner-preservative, liquid |
| Volume | 100 ml ± 4.5 % |
| Container / dispenser | bottle, pharmaceutical pump with long rotary nozzle |
| Base | isopropanol with dimethicone |
| Dry residue | ≈ 3 % (silicone film) |
| Drying time | 2 minutes |
| Freezing temperature | does not freeze |
| Storage conditions | −20…+30 °C, tightly sealed; shake if cloudy |
| Shelf life | 24 months |
| Hazard classification | flammable liquid cat. 2 (H225), H319, H336 |
| Regulatory document | TU U 20.59-42831345-01:2021 |
| Manufacturer | Ukraine |
| Barcode | |
| Article number | MM-DR-007 |
Safety measures. Dangerous! Highly flammable liquid and vapor (H225). Causes serious eye irritation (H319). May cause drowsiness or dizziness (H336). Keep away from heat, sparks, open flame, hot surfaces. Do not smoke. Do not spray on powered equipment and connected battery. Do not apply to optics, VTX radiators and boards for soldering. Use outdoors or in a well-ventilated area. Do not inhale vapor. Avoid contact with eyes; if contact occurs, carefully rinse with water for several minutes. Keep away from children. Do not swallow.
Frequently Asked Questions
Preservative or “Dry” + “Connector Protection”?
Preservative — when you need to work quickly and in the field: one pass with the nozzle. The “Dry” + “Protection” pair — when control is needed: separate clean contact (for example, before soldering), separate denser film with a drop.
Can you treat a flight controller board?
No — silicone on the board interferes with soldering and conformal coating. For boards — “Dry”.
Do you need to rinse before the next cleaning?
No. The next preservative treatment washes away the old film and applies a new one.
Payment by Bank Card
- On the website, via the secure payment service Wayforpay, Google Pay, Apple Pay
- To the Nova Poshta courier
- This payment method is not available in all cities of Ukraine. Please check the exact information with the Nova Poshta contact center at 0-800-500-609
- At a Nova Poshta branch
Cashless Payment for Legal Entities and Individuals
- After placing an order, our manager will send the invoice to your email.
- Payment must be made within 3 banking days
Note:
- If you pay for your order by bank transfer, we will ship it after the funds are credited to our account.
- You can collect your paid order by presenting the original power of attorney or the company’s official seal
Nova Poshta Delivery
After your order is shipped, you will receive a notification with the express waybill number.
Note:
- All products are inspected and insured for their full value before shipping.
- Orders are shipped via Nova Poshta every 3–5 days. Requests received later are processed the following day.
- When receiving your parcel, you must check the goods at the Nova Poshta branch in the presence of their staff.
- If the packaging is damaged or the goods have mechanical defects, please call: +38 (073) 324 00 00. For store partners, an individual delivery schedule applies.
Ukrposhta
Note:
- Orders are shipped every Thursday upon prepayment.
Cash on delivery with Nova Poshta or Ukrposhta, as well as bank transfer payments, are available for orders starting from 300 UAH. If these payment methods are more convenient for you, please increase your order amount. Thank you for your understanding.
Reviews
Clear filtersThere are no reviews yet.